Autotek SM1400.4 Spezifikationen PDF herunterladen (Seite 4)

AMPLIFIER FEATURE DESCRIPTIONS

STREET MACHINE AMPLIFIERS:

Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the mono amps All Autotek amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and amplifier DC

faults indicated by the red “PROTECT” LED.

which are capable of 4, 2 and 1-Ohm loads.

CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU WILL CAUSE

The input sensitivities for rated output powers are variable from 0.2V to 5V on the multi channel amplifiers and 0.2V to

DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE WARRANTY PRINTED IN THE BACK

6V on the mono models.

OF THE MANUAL. 2 & 4 Channel amps are capable of 4 and 2-Ohms wired stereo and 4-Ohms wired mono

All crossovers are fully variable in their respective ranges.

Crossover filters are 12dB/Octave.

bridged. The mono amps are capable of 4, 2 and 1-Ohm.

A POWER LED indicates the powered up and turned on condition.

-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying daisy chaining of amplifiers.

-SUBSONIC: Allows you to adjust the crossover filter from 15Hz to 55Hz.

-LOWPASS: Allows yo to adjust the LOW PASS crossover filter from 40Hz to 150Hz.

LEVEL: Adjusts the input sensitivity from 0.2 volts to 6 volts.

BASSBOOST: 45Hz bass boost adjustable from 0db to 12dB.

REMOTE CONTROL: This is the input jack for the remote Level control.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal.

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the amp not covered in the warranty.

SM3200.1 / SM4800.1 / SM6000.1 MONO BLOCK AMPLIFIERS

The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of controls. 1 set for channels 1 & 2 and 1 set for channels 3 & 4.

In addition, the 4 channel models have a Mode switch which allows you to select 2, 3 or 4 channel operation. Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and

the unit will automatically supply signal to channels 3/4. Select 3 channel when you only have RCA’s in CH 1/2 but plan to run channels 3/4 bridged. Select 4 channel if you

are providing RCA’s to channels 1/2 and 3/4.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying daisy chaining of amplifiers.

-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 1.2kHz.

-FULL: Bypasses all crossovers for full frequency range operation.

-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 5V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal.

-BASS EQ: Adjustable 45Hz bass boost from 0dB to 12dB.

Note that the LOW PASS signal is MONO.

-In the LPF position, the HIGH PASS filter acts as a subsonic filter.

-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS -EQ is also switched in.

SM1400.4 4-CHANNEL AMPLIFIERS

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying daisy chaining of amplifiers.

-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 1.2kHz.

-FULL: Bypasses all crossovers for full frequency range operation.

-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.

-BASS EQ: Adjustable 45Hz bass boost from 0dB to 12dB.

MODE: The mode switch allows you to choose Stereo for full range 2 channel operation or MONO for bridging operation

HIGH INPUT: If your radio/CD player does not have unbalanced (RCA) outputs, you can use the HIGH level (wire) inputs.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 5V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal.

Note that the LOW PASS signal is MONO.

-In the LPF position, the HIGH PASS filter acts as a subsonic filter.

-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS -EQ is also switched in.

SM1600.2 2-CHANNEL AMPLIFIERS

LINE OUT LINE INPUT

R R

L L

+ - gnd - +

HI INPUT

5V 0.2V 0dB 12dB 60Hz 1.2KHz 30Hz 250Hz

LEVEL BASS EQ HPF LPF

FULL LPF HPF MONO STEREO

X-OVER MODE

OUTPUT INPUT

BASS

BOOST

SUB

SONIC

LOW

PASS

LEVEL

REMOTE

CONTROL

POWER

PROTECT

R R

L L

0dB 12dB 15Hz 55Hz 40Hz 150Hz 6V 0.2V

CH3/4

CH1/2

LINE INPUT

LINE OUTPUT

CHANNEL 1 / 2

CHANNEL 3 / 4

LPF

HPF

FULL

X-OVER

5V 0.2V 0dB 12dB 60Hz 1.2KHz 30Hz 250Hz

LEVEL BASS EQ HPF LPF

2 3 4

MODE

+ - gnd - +

HI INPUT

Ch3 Ch4

Ch1 Ch2

+ - gnd - +

R R

L L

1 2 3 4 5 6 7 8 9 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Autotek SM1400.4 Spezifikationen Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audioverstärker Autotek SM1400.4